Category: Tutorial

Tiny Sophia Bag HACK: Travel Sanitizer Holder

As the world goes on, we know washing hands and using sanitizer is LIFE right now. It is SO important to stay healthy and protect ourselves against all germs – pandemic or not!  Washing hands with soap is the preferred way to keep them clean, but when there isn’t a sink around hand sanitizer is a decent alternative. You can read more about the benefits of hand-washing here with the CDC.

Like all of you, I want to keep my family safe and have sanitizer on them at all times – especially as school opened up for my kids. But of course, supplies have been (and still are) very bare.  Trying to find those manufactured jelly style travel sanitizer holders was just impossible. That’s when I took it upon myself to make cases for my kids and husband.

Different size travel bottles

It turns out that the Tiny Sophia Bag (read about it here) is the right width to hold most travel sanitizers! The height just needs to be adjusted and that’s where this hack was born. This hack will take you through the steps to transform your #tinypurse to a sanitizer holder for most 1-2 oz travel bottles.  I tried to find a variety of bottles to test so you can see how they fit and decided to create one version for bottles from 1-1.6 oz and then another version that can fit 2 oz bottles.  If you are using bottles different from any of those pictured, be sure to check the template against your sanitizer BEFORE cutting any material.

2 oz Holder vs 1 oz Holder

 

 

Materials Needed:

  • The Tiny Sophia Bag pattern – found here
  • Ruler
  • Extra paper
  • Marking Instrument
  • Clear Tape

Tutorial

***Please note there are adjustments depending on whether you are making a holder for a 1.0-1.6 oz. bottle versus a 2 oz. bottle.   Please read instructions carefully.

1. Cut the pattern template out per instructions. Mark the cut line along where the bottom flap meets the sides.

2. Take a scrap piece of paper (wider than the bottom flap) and mark a 1″ high extension for 1-1.6 oz. sanitizer bottles. *If you have a 2 oz. bottle, you will want to mark a 2″ high extension.

3. Cut the bottom flap off the bag template following your markings

4. Line up the top of the pattern along the extension and tape into place.

5. Take a ruler and mark the right side of the extension aligning it to the Top flap’s side edge.

6. Repeat on the left side of the extension.

7. Line up the bottom flap to the lower side of the extension making sure it matches the side markings.

8. Trim away the excess paper.  Mark a line 1/2″ from the top of the extension. *If you are making a 2 oz. bottle holder, mark a line 1″ from the top of the extension.

9. Use a sanitizer bottle cap as your opening.  (This replaces the Charger Opening.)  Center it vertically on the template and place it just under mark made in the previous step.  Trace.

10. Carefully cut out the circle with paper scissors.

11. Check that the sanitizer bottle you want to use fits through the opening on the template. Adjust as needed.

12.  Check that the template fits around the bottle by aligning the hardware holes.  Adjust as needed.  Once you are satisfied with the fit, follow the steps in The Tiny Sophia Bag to finish your  travel sanitizer holder!

Notes:

This cork version uses the 1 oz adjustment, but if I were to make it again just for this style of sanitizer bottle from Bath & Body Works, I would make a slightly wider opening to accommodate  that wider flip-cap.

I added stitching to all of my samples in this post, but you don’t have to.  Using faux leather with felt backings like these pictured above leave no fraying and make this a fast and simple project.

With the holidays ahead, these will make such great gifts!  So I will switch up the hardware to swivel clasps on the back so they can hang easily from key chains, purses and backpacks.

Where to find supplies:

  • For Cork or Faux Leather, I’m a big fan of Sew Sweetness.  Shipping is flat-rate, fast and I think a great deal!
  • For real leather and a variety of finishes, TanneryNYC has remnant bags.  I received small – medium sized cuts and was able to make several Tiny Sophia Bags out of the surprise shipment. These are high quality pieces of soft leather.
  • I love Emmaline Bags and By Annie’s hardware, but if you are looking for a value set for kids, I recently bought these (pictured on yellow case) and these from Amazon.
  • For Snaps, I used spring style ones from Gold Star tool, but recently fell in love with these Rivet Magnets from Kam Snaps (as seen with the pink cork version above.)

 

I hope you enjoy this hack and find it useful in our current environment.  Please drop a comment and let me know what you think!

 

Hugs and Stitches,

Cristy

 

This post may contain affiliate links.  Any earnings go right back into powering this website.  Please read my Disclosures here.

Add Puff Sleeve Drama with a Sheridan Sweater Hack

This post was originally published on the Hey June Handmade Blog in January, 2020.  Edits are in italics and additional pictures have been added (since I love this pattern SO much!)

When I first hacked this Sheridan Sweater for the Hey June Handmade Blog, I had no idea it was going to become one of my MOST worn tops. Prior to March, life was pretty normal while we were just starting to hear about the pandemic. My social world was still moving along and was able to wear my Sheridan to Lunar New Year celebrations (as planned!), Galentine’s Day fun with my girls, and was my go-to for a night out.  I knew even back then that I wanted another Sheridan.

After a #sewingfail with the wrong fabric (it was a red and cream colored stripe that clashed and looked HORRIBLE with my skin tone and hair highlights,) I was ready to make another.  This time I wasn’t going to mess around.  I knew I would ADORE my new Sheridan because I used…the same hack…and the same fabric as my OG…just a different color!

 

Back in early December, I knew I needed a new red top.  My one cardigan just wasn’t enough for all of the holiday school parties, concerts, church events and even family get-togethers.  I wore that one piece of red clothing OUT and knew I needed something else to add to my festive wardrobe.  But did I really need a new top???  Did I really want to make one??? Then the Sheridan Sweater was launched and my questions were answered.

All of my internal fighting against wanting “another” knit top disappeared.  After seeing the Sheridan launch, my mind switched and I bought the pattern right away.  Of course, I need  a new red top!  It WILL work through the holiday season, AND into the Lunar New Year AND be useful for Valentine’s Day school parties!  Why wouldn’t I need the Sheridan Sweater in my life?!?

Adrianna did a fantastic job designing the different views and I’m obsessed with the seamless funnel neck, which I haven’t seen in any other DIY pattern.  The Sheridan Sweater also has the big statement sleeves which is on still on trend and I knew both of these features would really stand out in red.  But since this was going to be my all-winter holiday top, I wanted to bring it up juuuuust an extra notch.

FABRIC

I found this beautiful textured waffle knit from Telio fabrics.  One of the reasons this sweater has been on constant wardrobe repeat is the fabric.  As a poly/spandex blend, the color saturation is on point.  After all of the washing and drying I’ve done, the color still looks as intense as day one.  I was concerned that the texture might be lost over time with dryer heat, but it’s all still there!

The Paola Pique Liverpool’s medium weight was a perfect complement to this pattern.  It has great body and really shows off the full sleeves.  The stretch and recovery is also very nice.  When I pull up on the sleeves and adjust the waistband, it  holds it’s size well and doesn’t stretch out over the course of the day.  This fabric comes in so many rich jewel tones that I had to have the Emerald.  The pictures come up more teal, but this color swings more to the green side in-person.

TUTORIAL

I figured if I was going red, I wanted to make the sleeves stand out even more. So….I hacked the sleeves to be more voluminous in the sleeve head for All. Of. The. Drama.  Below is my quick and definitely non-technical way to achieve that extra shoulder poof.

1. Take the sleeve pattern and make a copy.  (I traced the pattern onto some Swedish tracing paper I had on-hand.  I like using this since it’s more pliable than regular paper and can be pinned/sewn without being destroyed.)

2. Divide the sleeve into approximately 4 equal sections by width.  With the nice notch markings already drafted as part of the pattern, I used these as guide when splitting the sleeve.

3. Cut the pattern to separate these sections from the sleeve head all the way down to the cuff, but NOT cutting through.  All of the sections should be hinges and able to move.

4. To start, I added 1” in between each section.  I placed scrap paper underneath the pattern, and hinged each section out by 1” at the sleeve cap.  Then I taped the pattern onto the scrap.  Repeat 2 more times between the sections.  If you would like more volume, you can increase the hinge widths.

5. To get the extra volume at the top of the cap, I added 3/4” to the top and blended the line back to the notched parts of the cap, all while following its shaping.  Again, if you want a little more puff in the sleeve cap, feel free to add a little more to length to the top.

6. At the cuff line, true up the pattern so it is straight again.

At this point, I cut out the pattern and did make a muslin, but only had quilt cotton on hand.  It gave me an idea of the extra volume and shape added to the sleeve.  I did have to consider the extra weight and stretch with the knit fabric.  But it was still good enough for me and I went ahead to cut into the main fabric.

To insert the sleeve, I made gathers between the sleeve notches not exactly knowing how it would all look.  But I ended up marking 3” on either side of the shoulder seam and pushed all the gathers in between those markings.  I basted the sleeve into place and was very happy with the result!  With that, I finished sewing the sweater and have never been more pleased!

This hack turned out exactly like what I wanted and just love how “extra” the sleeves are.  The additional gathers and volume in the sleeve cap really balance out the overall ease in the sleeve and I love the extra long cuff to show it all off.  This top is pretty fancy and ready for every occasion now.  It’s still comfy in a stretch knit, but also so incredibly unique and special!

Project Summary

  • Pattern: Sheridan Sweater by Hey June Handmade; View: B; Size 10
  • Mods: Narrowed shoulders by 1/2″ each, increased the cropped length by 1″, used Puff shoulder hack above
  • Fabric: Telio Pique Liverpool Knit from Fabric.com in Hermes Red and Emerald

This hack can be used on just about any pattern with a set-in sleeve.  I may have to try it on a woven pattern this fall/winter.  Please let me know in the comments if you use this hack!  I would love to hear what you think!

 

Hugs and Stitches,

Cristy

 

This post may contain affiliate links.  You can read my full Disclosure here.

 

Full Zip Hack with the Grace Rashie Pattern

2 Comments

When I first hacked the Grace Rashie by Swim Style Patterns two years ago, I never documented the process…Big mistake, I know!  It was one of my late night experimentations which you can find here.  I honestly didn’t know if it would work or not and got so wrapped up in the process that I didn’t write down measurements or take photos of my complete step outs.  But luckily, I knew I needed at least a second rashguard for myself and made sure to document it this time!

Supplies Needed

Tutorial

Step 1:  Cut all pattern templates according to instructions.  Pull out the “Front Section” and add 1/4″ to the center-front as shown.  You will cut at the dashed line for just the “Top.”

Note: I made a size M and all measurements for center front, zipper guard, and zipper are ALL for this size.  You will have to adjust as needed for your sizing.

Step 2:  Cut all fabric according to instructions EXCEPT for the “Front Section.”  Instead of cutting the “Front Section” on the fold, you will cut TWO separate mirrored pieces using that 1/4″ you added in.

Step 3: Cut (2) 19 1/4″(length of the center front)  x 1/2″ strips of interfacing and fuse to each wrong side of the  center “Front Sections.”  Set aside.

left side of image is the Bottom and the right side is the Top

Step 4:  Cut (1) 19 1/4″ (same as length of center front) x 3″ strip of Main Fabric for the Zipper Guard.  Fold the fabric lengthwise with right sides together and press with low-heat iron, if needed. Mark seam with 1/4″ at the bottom.  For the top, measure 1/4″ down at the raw edge and then 1″ down on the folded side.  Connect the two points with a curved line as shown.  It doesn’t need to be precise!

Step 5: Sew on the markings you made. (They don’t need to be serged, but I went ahead and serger the seams while my machine was set up.)

Step 6:  Flip the Zipper Guard right side out, pushing out the bottom corner and the top curve.  Press with a low-heat iron.  Match the raw edges and finish with serger or zig-zag stitch.  Set aside.

Step 7:  Prepare Zipper by folding down the excess tape above the top stoppers.  Tack the fold into place approx. 1/8″ away from the edge.  Trim the overhanging tape.  (If you are making size L, you might be able to skip this step and use the full length of the zipper.)

***Follow instructions to complete the Grace Rashie (skipping all zipper steps.)  When you get to the hem, double check that the length of the finished center front matches the length of the zipper.

Step 8: With the wrong side of the Zipper facing up, add Wonder Tape to each long side of the tape.

Bottom

Top

Step 9:  Separate the Zipper and lay one zipper side down on the stitched side of the Zipper Guard.  Pictured is the LEFT side of the zipper (without the head,) but my previous version had the head with the guard.  I honestly don’t know which side of the zipper should sit with the guard, is technically correct.  I was playing to see if there was any real difference in how it wore on the body and I didn’t feel anything different…

Step 10:  Fold the Top of the Zipper Guard over Zipper and tack into place with 1/8″ seam allowance.

Step 11:  Working on the LEFT side of the garment, match the center front of the Rashie with the Zipper Guard, right sides together.  Use a zipper foot and sew itogether with a 1/4″ seam allowance.  Open the Zipper Guard and press seam allowance to the back.  Top-stitch 1/8″ from the edge of the Zipper, going through the Main Fabric, Zipper, and seam allowance.  Repeat with the RIGHT zipper.

Congratulations!  You now have a custom swim rashguard to protect your skin against the sun and elements.  I love having these for the cool winds of the lake.  The best part is when the rashguard gets wet, I can easily zip it off!

Please let me know how this tutorial worked for you!

 

Happy Sewing,

Cristy

 

This post may contain affiliate links.  Please read about my Disclosures, here.

Fabric Face Mask Tutorial Using Ties

When schools shut down in mid-March for my kids’ school, I knew something big was happening.  In addition to US news, I follow a lot of news out of Asia and the outlook was pretty bleak for us in the states.  So when the government, along with a multitude of healthcare organizations said we short on Personal Protective Equipment (PPE,) I was shocked.  But then came the pleading of all sewists to start making fabric masks…and I was just like you…How can a FABRIC mask do anything against an airborne VIRUS???

But I fell in line like a good soldier and just started making masks with the guidance given by the CDC and a host of other online resources.  Initially, I tried out this Fu Mask version that was more contoured to the face, but it left a lot of room around my cheeks and even my husband’s (which is more full with a  beard.)  The fit was not the greatest and I ended up folding a dart in to take out the excess room.  However,  I knew if I was going to make and donate masks, I needed to make a version that was going to fit the largest range of faces AND be conducive to production sewing…aka…sewing a TON of them at a time.

The standard pleated surgical style was it.  The rectangle shape makes it a quick sew and the pleats allow a roomy fit for all different face shapes.  But instead of over-the-ear elastic, I chose to use fabric ties help accommodate for different head sizes and for medical sterilization purposes.  Early on, we just didn’t know how elastic would hold under continuous high temperature washings at medical facilities.  Also, elastic was hard to come by with everyone making masks for the lack of national PPE supplies.  My first 200 donations went to private practice doctors, police officers and workers at a mental health facility.  So I wanted to make sure these could all be cleaned in industrial washing machines without compromising the integrity of the elastic.  With all of this, I also had to choose a style that I could personally make the quickest way.  So this is the technique I used.

Click into my video below to watch the entire mask-making progress.  You will need:

  • (2) 9″ x 7″ rectangles of fabric – one for lining and one for exterior.  I used fleece for the lining when it was still cooler outside, but then switched to quilt cotton for both layers once weather began to warm up.
  • (4) 18″ Ties – These can be make from bias strips as shown in the video but can be swapped out with  twill tape, ribbon, shoelaces, and even piping rope.

Although, the first few months of the pandemic were quite frantic with home-schooling and then  making masks, I’m still so thankful to have the gift of sewing in my life.  I felt my heart swell with every mask made and delivered to those working on the front lines. <3

 

Take care of your loved ones and WEAR THAT MASK!!!!

Cristy

Create Card Slots in the Kelly Waist Bag

When wearing a waist (belt, bum, fanny pack) bag, space is incredibly limited. There is already a nice built-in slip pocket to the Kelly Waist Bag (a FREE pattern you can find here.) But I thought I could kick it up a notch and add some card pockets — perfect for just that ID and credit card for a night out. The smaller slots keeps your cards more secure, yet easily accessible.

Make the Card Pockets

This is a very quick and simple add-on to the pockets. You will need the pattern which you can find here, plus an additional 6″ x 2 1/2″” piece of leather which I’ll refer to as the Card Pockets.

With the 6″ x 3″ Card Pocket, mark a line down the center with right side facing up. Take the Front Pocket piece and lay it right side up and then lay the Card Pockets with right side facing up aligning the bottom edge and corners. Clip into place.

Sew on top of the Card Pockets on the marking attaching the Card Pockets to the Front Pocket and also dividing it into two.

Continue to Step #6 to finish assembling the rest of the pocket.

Project Summary

I hope you enjoyed this simple tutorial to add card pockets to your Kelly Waist Bag!  You now have an extra layer of storage while being hands-free.  Head to the Pattern Resources page for all Love You Sew pattern hacks!

 

Hugs and Stitches,

Cristy

 

This post may contain affiliate links which helps keep this website going.  You can read all the info regarding these links in my Disclosures.